| Prod Model: |
HIP-58 |
| Markets: |
North America,South America,Eastern Europe,Southeast Asia,Africa,Oceania,Mid East,Eastern Asia,Western Europe |
| Capacity: |
100L 150L 200L 240L 300L |
| Structure: |
Compact Type |
| Pressure: |
Pressurized |
| Interior Material: |
Stainless Steel |
| Collector Components: |
Glass Vacuum Tube |
| Certification: |
CE |
Product Description
100LITER 150LITER 200LITER 300LITER Heat Pipe pressurized compact solar water heater
HIGH PRESSURE HEAT PIPE SOLAR WATER HEATER make better bathing experience.
1 direct heating, high efficiency
2, the pressurized hot water
3 parts of 1%, offered freely
4 CE, Solar Keymark EN12976
5, factory price
Compact Pressurized Heat Pipe Solar Water Heater Feature
1) highly efficient absorber of high performance with daily average efficiency over 50%.
2) sudden onset, heat pipe transfers the heat energy into the storage tank in one direction.
3) stand the pressure of 6 bar, you can connect directly with tap water.
4) No water in vacuum tubes, the system can operate even with several tubes breakage.
5) high efficiency insulation with polyurethane foam.
6) Simple structure, easy to assemble and install.
7) it Can be used throughout the year in the cold weather.
8) Can be used together with auxiliary electric heater.
9) stable and reliable performance.
10) Environmental protection and energy saving.
11) pressurized hot water will make your bathroom more comfortable.
Principle Pipe Solar Water Heater compact heat pressure:
The key pact heat pipe solar water hater pressure heat pipe, the heat pipe is hollow with the space inside evacuated, the same as the solar tube. In this case, isolation is not the objective, but rather to alter the state of the liquid inside. Inside the heat pipe is a small amount of purified water and some special additives. At sea level, water boils at 100 ° C (212 ° F), but if you climb to the top of a mountain the boiling temperature less than 100 ° C (212 ° F). This is due to the difference in air pressure.
Based on this principle of boiling water to below the lower air pressure, by evacuating the heat pipe, temperature can achieve the same result. The heat pipes used in AP solar collectors have a boiling point of only 30 ° C (86 ° F). So when the heat pipe is heated above 30 ° C (86 ° F), the water evaporates. This discharge VA rises quickly the top of the heat pipe heat transfer. As heat is lost in the condenser (top), pouring condenses will form a liquid (water) and returns to the bottom of the heat pipe to repeat the process again.
The top of the tube was pluged heat in the water tank, so that the cold water in the tank can get heat pipe heat and become hot water. Because the water tank is close, so it can withstand 0.6Mpa (6 bar) when the current enters the water tank from the lower entrance, the hot water is off the jack on the top, the like the electric water heater.
| Technical parameters of heat pipe solar water heater compact pressure |
| DESCRIPTION | heat pipe solar water heater |
| TANK MATERIAL OUT | 0.4mm galvanized steel / stainless steel SUS304 0.4mm / 0.4mm SUS304-ba (bright) |
| INTERNAL MATERIAL DEPOSIT | SUS304-2B 1.2mm stainless steel or steel SUS316 steeel |
| TANK insulating layer | 50-60mm high density polyurethane foam |
| Diameter of the outer tank / inner | 470 / 370mm |
| ELECTRIC HEATER | 1500w; 220v / 110v |
| AND OUT OF HOLE | Men 1/2 ", 3/4" |
| MAX PRESSURE | 1.2Mpa |
| TUBE SOLAR COLLECTOR | 3.3 borosilicate glass with AL / AL-ALN / ALN (only white) or CU / SS-ALN / ALN (three target) |
| THICK GLASS TUBE | 1.6mm |
| VACUUM TUBE SQUEEZE | P ≤0,005 pa |
| ABSORPTION | As = 0.93 to 0.96 (AM1.5) |
| EMISSION RATIO | Ε h = 0.04-0.06 (80c ± 5c) |
| IDLE PARAMETERS OF PROPERTY sunbathing | Y = 220 ~ 260m ². C / kw |
| Average heat loss coefficient | Ult = 0.6 ~ 0.7 W / (m2. C) |
| SUPPORT: | Stainless steel 1.2mm / 1.6mm galvanized steel aluminum alloy / 1.5mm |
| STRUCTURE OF TANK: | Generally holes for p / t valve inlet and outlet water, electric heater, magnesium rod, the measure will be welcomed warmly. |
| WELDING: | Automatic argon arc welding |
| PARTS OF CLOSURE: | Stainless steel screw |
| SEAL MATERIAL | Stabilized high temperature silicon |
| Opition: | SR609C controller system, electric heat control and temperature display |
Haining Qiruite Photoelectric Co., Ltd. was founded in 2001 and specialized in producing of solar water heaters(mainly), solar lights. In addition, we also have the capacity of researching, developing, designing, manufacturing and installing large scale solar-heat-collector projects and its central-control system. Our factory covers an area of 28, 000 square meters and has an annual production capacity of 100, 000 solar water heaters.
We trust product quality is our life. Therefore, we have got the certificates of Solar keymark, CE, ISO9001: 2000 and CCC. Our production line include over fifty working procedures, and we manipulate strictly under the measure requirements and working order. Our products are exported to many countries with good honor, such as EU, North America, Middle East, South Africa, Southeast Asia and etc.
We can guarantee high product quality. According to different individual requirements such as area, climate and consumption level, more and more productions come into the market from Qiruire. All our successes are based on the research and analysis of the market. If you are interested in any of our products, please feel free to contact us without hesitation. and we are looking forward to having opportunities to become your future honor supplier.
